Attentions to ceramic epoxy adhesive when ceramic installation

Except ceramic tile liner,  rubber ceramic wear liner ,ceramic elbow pipe liner,hex tile mat,alumina grinding balls etc, Chemshun Ceramics also provide ceramic epoxy resin adhesive for wear resistant ceramic installation. detailed ceramic epoxy adhesive application process as follows :
1. will be sticky surface grinding rust; if oil, the application of 99% acetone cleaning: If the bonding surface is non-metallic, the surface should be polished, coarsening. This step is for bonding firmly. 
2. Mix the glue evenly, press A: B = 4: 1 (weight ratio) mix, mix thoroughly, apply to the surface of the object to be bonded, in the wear-resistant ceramic adhesive surface is also coated with glue, as required bonding and rubber Hammer hit, so that bonding firm, hardening at room temperature 2h.
3. Room temperature curing 8h, the rubber hammer can be used to check the sound to determine whether the phenomenon of lack of plastic, if the phenomenon of lack of plastic, wear-resistant ceramic should be up, local re-bonding. 
End users need pay attention to some problems when use ceramic epoxy adhesive, details like following items: 
1. In the rainy season or the construction site is moderately large, if the bonding surface for the metal material, should be polished immediately after grinding to prevent metal rust.
2. glue should be A: B = 4: 1 (weight ratio) accurate ratio, it is recommended to arrange the preparation of glue, in order to avoid the proportion of glue is not accurate and the construction quality problems. 
3. glue configured, it will soon cure, should be used within 40min, with the use of configuration. 
4. When the construction site temperature is below 10 ℃, the adhesive strength of the glue will change, especially when the temperature is lower than 0 ℃, the glue will freeze, it seems to have cured, but in fact no bonding strength, the user in use There will be a drop phenomenon. Therefore, under low temperature conditions, should be heated curing (iodine tungsten lamp heating), the surface to be bonded to about 30 ℃ (not more than 50 ℃), adhesive bonding, heating until curing. Noting the above problems, after construction and construction, there will not be a wide range of problems, the side to improve the production efficiency.

 Rubber ceramic wear liner is hot seller products because of its high impact and abrasion resistance. it can be installed by ceramic epoxy resin diretly . more information needed ,welcome to inquiry  by office@chemshun.com

评论

发表评论

此博客中的热门博文

What are the characteristics of abrasion-resistant ceramic tiles?

What are the characteristics of abrasion-resistant ceramic tiles?  Abrasion-resistant ceramic tiles are widely used in many projects, in the pit furnace is also built with a wear-resistant ceramic tiles, wear-resistant ceramic tiles not only to fire resistance, high temperature requirements, but also to wear requirements, Introduce the impact of wear-resistant ceramic tile wear-resistant factors which have! Abrasion resistance of  abrasion-resistant ceramic tiles  depends on the composition and structure of wear-resistant ceramic tiles. When the abrasion-resistant ceramic tiles are composed of dense polycrystals composed of single crystals, the wear resistance depends on the hardness of the mineral crystals. High hardness, high wear resistance of the material. When the mineral crystals are non-isotropic, the grain size is small and the wear resistance of the material is high. When the material from the multi-phase composition, the wear resistance of the material with the bulk
阅读全文

What are interlocking wear-resistant ceramic tile liner ?

图片
  The shape of ordinary wear-resistant ceramic tiles is a square sheet structure, and they are arranged in rows and columns. There are linear seams between the rows and columns of wear-resistant ceramic sheets. The linear seams along the direction of fluid flow are A smooth fluid scouring gap is formed.      In addition to the normal wear of the fluid on the surface of the wear-resistant ceramic sheet, the erosion gap becomes a breakthrough door for the fluid to wear the side of the ceramic sheet. Under the long-term erosion of the fluid, the seam will gradually widen and the degree of wear will become more and more serious. , the change of connection affects the service life of the wear-resistant ceramic sheet, which in turn affects the protection effect of the anti-wear parts. After this kind of wear-resistant ceramic sheets are pasted, the adjacent ceramic sheets do not have an interlocking effect with each other. The pasting is not strong during installation or they are easy to fal
阅读全文

Development of Ceramic Materials

图片
Ceramic is the oldest material, and it is the first chemical product made by human conquering nature. It appeared much earlier than metal materials. It is one of the symbols of human civilization and an important research object in the history of human civilization. For a long time, the development of ceramic materials relies on the teaching of craftsmanship. The products are mainly household utensils, building materials (such as bricks, glass), etc., usually called traditional ceramics. Due to the development of materials science, people have a deep understanding of the relationship between material structure and distribution. They can successfully control the chemical composition and micro - structure of lattice materials and successfully develop ceramic materials with different properties. For example, high-temperature structural ceramics and various functional ceramics (electronic materials, optical fibers, sensitive ceramic materials, etc.) have been more and more widely used, an
阅读全文